Adding PS6100x to PS4000XV
Hi.I got a PS4000XV with 16x 600 GB 15K SAS.I will be getting an additional PS6100x with 24x 600 GB 10K SAS.Questions:1. Can I join the PS6100X to my PS4000XV pool in order to expand existing capacity...
View ArticleReplication between PS6010 and PS410 issue
Dear FriendsWe need to backup volumes at old array to new array- Old array ( PS6010 with firmware V4.3.6 ) - Old Group- New array ( PS4110 with firmware V7.0.9 ) - New Groupafter i configured...
View ArticleEHCMService Question (38,000 handles)
I inherited a problem SQL server a few years back. It is a 2008R2 VMWare with Dell SAN storage.I have this issue with it crashing out and reporting 5719 errors after running fine for about a month. It...
View ArticlePS6210 - Can it negotiate with 1Gbps switches?
I was wondering if anyone knew if the PS6210 supported negotiating at 1Gbps instead of 10Gbps? We'd like to leverage this capability if possible as an interim solution until we get 10Gbps switches put...
View ArticleReplicas not getting cleared out of SAN - Equallogic 6100
I have experienced this now several times where the SAN is holding on to old replicas and saying there are 21 to 24 replicas even though I have it all set to 10 replicas on the volumes . I have to go...
View Articlepower edge to raid
can someone post a wiring diagram to connect 2 poweredge R420 to PS6210 raid.
View ArticleHIT for RHEL 7
When is support comming for RHEL 7 based installations ? We are getting ready to turn up a RHEL 7 based datacenter and we can't seem to find a HIT for Equallogic
View ArticleGet data from offline volume (member down)
Hello, I have two PS4000E in Group01>Pool01. One PS4000E has been reset to default factory by human mistake. Is there any chance I can get some of the data from the remaining member. The data is...
View ArticlePS4000 unable to clear foreign disk label
We have recently purchased new disks from Dell. However, all the added disk are shown as foreign disk. We followed the instruction to add to RAID and allow clearing data. Within a few seconds, the...
View ArticleManual drive failover in PS6010
Hello all,I am wondering if there is a way to perform a manual drive fail-over to hot-spare in a PS6010XV with 16 x 600 GB 15K SAS disk drives installed.. When a PS6010XV enclosure that has...
View ArticlePerformance has deteriorated. I/O latency increased
We have two PSM4110 and 4 ESXi 5.5 U2 (Enterprise plus). I did installed Dell Mem and rebooted servers. I see path selection is Dell_PSP_EQL_Routed selected. ESXi servers are only connected to this...
View ArticleMigration from M1000 chassis and from Old Equal array - Questions
Hello'sWe are planning a migration from an old M1000 to a newer M1000. In addition, we will be migrating from an old PS array to a newer one. The environment is 100% virtual - Vmware. There also exist...
View ArticleCommunication port for Powershell
Can someone advice what port does Powershell use to connect to PS6510? I want to make sure our firewall only allow this port available for powershell but it seems that there is always communication...
View Articlereplacing EQL in a group
hi there,We currently have a EQL group comprising of a PS4000 and a PS4100.I've been asked to replace the PS4100 with a new PS4100X and wanted to check my plan is ok. As I understand it you can only...
View ArticleGet data from offline volume (member down)
Hello, I have two PS4000E in Group01>Pool01. One PS4000E has been reset to default factory by human mistake. Is there any chance I can get some of the data from the remaining member. The data is...
View ArticleUnable to to get 2nd MPIO connection to stay connected
I have several R720 servers with dual port Broadcom BCM57810 10Gb NICS. They all have Windows Server 2012 R2 Datacenter installed with the Hyper-V role. I am trying to make iSCSI connections to a...
View ArticleHIT for RHEL 7
When is support comming for RHEL 7 based installations ? We are getting ready to turn up a RHEL 7 based datacenter and we can't seem to find a HIT for Equallogic
View ArticleCommunication port for Powershell
Can someone advice what port does Powershell use to connect to PS6510? I want to make sure our firewall only allow this port available for powershell but it seems that there is always communication...
View ArticleClik here to view.
San headquarters enigma...
Hi, We have a PS4000, loaded with 15K 600Gb SAS drives configured as RAID10. The unit is pretty quiet (in the main - see below) only a couple of Poweredge R710s connected running SQL 2008 active active...
View ArticleEquallogic PS6110E & FS7500 NAS Issue
I cannot get the configured NAS cluster to come online. Group Manager shows a status of "unknown" on the NAS cluster itself, but the other storage pool seems to be working fine since all of my VMs...
View Article